- OEMs can replace the 2-parts configuration of the Hexagon Bolt Pin+Minus screw blind with a single 8mm bolt.The 8mm bolt is also used frequently for maintenance around the brake area, so the assortmen...Đọc thêm
- I thought it was a cheap Front and Rear Set and installed it on my early BAJA, trusting the fitment guarantee, but it was too long in both directions compared to the front and rear pins, and it hit th...Đọc thêm
- The brake pin looked like oem quality and fit inside the caliper perfectly. DRC products are really good, a little bit expensive. I prefer hex head instead of allen. Especially when allen tend to take...Đọc thêm
- I had no problems, but since it is an old car, I replaced the brake pin to prevent it from sticking due to rust, and since it is integrated with the cap of the blind, I don't have to worry about losin...Đọc thêm
- I bought it because it seems to be resistant to corrosion.The original was corroded and was replaced while BrakeOverhaul.Đọc thêm
- I bought it because the OEM came out with Stages.It looks polished and has a high quality feel, and it is stainless steel, so I expect it to be rustproof and durable.The smooth surface may also improv...Đọc thêm
- When I did the Pad replacement, I saw that the Pin was stepped and worn.The minus on the cap of the pin was so hard that it was about to break, and I had to tighten it loosely, but if I licked it, the...Đọc thêm
- These are the parts that need to be replaced from time to time because of the decrease in the number of steps. The head is 8mm in the hexagon.You can remove it with TWrench, so it's easy to maintain.Đọc thêm
- I changed a lot of parts along with the brakeOHThe original Pin was textured with rustThis will make Maintenance a breezeOne thing I was worried about, though, is thatI was wondering if I could use So...Đọc thêm
- I changed it while changing the Pad of WR250XUnlike OEMs, Material:Stainless Steel, rust-resistant, slotted screwdriver for replacement You will be able to avoid usingI can't think of any other Merit ...Đọc thêm
- Removed OEM RetainerBolt, although there is no step, but rust and dirt are conspicuous, I think that I can reuse it if I polish But dare to exchange it to DRC.Easy to install, just remove and replace....Đọc thêm
- After buying a used WR250X, I installed it to fit a full overhaul around Brake It wasIf you are an OEM, you can use a slotted screwdriver before accessing the pin It is necessary to remove PinPlug, bu...Đọc thêm
- I think that it's worth it just getting better without removing the OEM's Minus screw.I am using Stainless Steel every time for various car models thinking that it is also strong against rust.Đọc thêm
- I used it for the compatible model but the length of Pin for the rear wheel Caliper is long and it seems to interfere with Spoke.Another Size of the other company's Motorcycle matched it, so I use...Đọc thêm
- DR-Z400SM (07 year) Was attached to,Front can be exchanged directly from OEM.For Rear, OEMSpec. As it is,Part of the Brake Body side that receives the end of the brake pin is tapered,Corresponding par...Đọc thêm
- OEM Screw will become unnecessary and rust will be less likely to occur so it will be extremely helpful. It is easy to maintain.The price is also cheap, so buy and there is no loss.Do not forget Greas...Đọc thêm
CỬA HÀNG LỚN NHẤT
TẠI NHẬT BẢN
COUPON ĐẶC BIỆT,
GIẢM GIÁ, KHUYẾN MÃI
DỊCH VỤ GIAO HÀNG
NHANH, MIỄN PHÍ