- I bought it because it said it was compatible with DJEBEL250, so I thought it would also be compatible with XC, but the shape did not fit and I could not install it.I contacted them in a panic to retu...Đọc thêm
- I am generally satisfied, but it would be helpful if the Bolt for adjustment were longer. I am using it almost all the way to the root.Also, I would like to see Clutch and Brake sold separately.Đọc thêm
- I always buy this.It is a spare in case of breakage, but it breaks quite a bit when knocked down, so if it bends even a little, it is replaced immediately.It is easy to grip and short, so it does not ...Đọc thêm
- [How is it used?Installed on TS125R.Application:Off-roadUsed for about 6 years. Many times overturned.Was the one you received as per Image?As shown in the image. Since my hands are so small, I needed...Đọc thêm
- I bought this as a spare for my wife's motorcycle. It is much easier to grip than the OEM and my wife noticed the difference. I think I'll use this for my motorcycle too.Đọc thêm
- I replaced the NORMALLever with this product because it got bent due to standing moss.Since the vehicle body is light and Caliper is a single push 2 pod, Brake can be operated without a problem even w...Đọc thêm
- Short lever can be described as RALLYI am satisfied with the texture, feel and CostLargeIt is a repeat order, but it is a long term relationshipĐọc thêm
- I changed it to install a Knuckle guard in FTRNORMALLever, it's too long to wearI feel like the pull is easier than NORMALThe exchange is easy and RecommendationĐọc thêm
- I really wanted a Foldable with a play adjustment Lever, but I didn't think so It was expensive and not a compatible carI chose this one as the only one that fits and is cheap and reputable because ch...Đọc thêm
- I installed it on my CRM250RR It was replaced due to a standing mock-up I was using other levers until they arrived, but the feel of the controls didn't feel right This Lever feels good when you pull ...Đọc thêm
- Mounting on XG250 TRICKERI could install it without any problem.Regarding length, it may be a bit too short for those who operate with three fingers.Đọc thêm
- I installed it on my CRM250 The same thing was attached before the exchange, but it was damaged and I replaced it with a standard type Lever I used to use it, but it didn't feel right, so I had to rep...Đọc thêm
- I had already attached to Motorcycle purchased in second handPo Drill at the first fallRecommended to VeteranRider when looking for the next LeverAccording to that personIt is better not to break abso...Đọc thêm
- In the case of the carburetorD tiger on which I am riding, I adopt the famous place because there are few Lever choices.I have just started using it, but I do not have any problem in using it.I feel I...Đọc thêm
- XTZ125 (CHINA) Mounting onBrake master cylinder Press Piston Screw and Nut purchase separately for SEROW (About 200 yen) Both Clutch and Brake are attached. The length of Lever is Ball 1 pc. It is an ...Đọc thêm
- I used it for DJEBEL.As the other person wrote, the position where Mistress Cylinder's Piston is pressed,I am out of alignment..I am pushing towards the edge of Piston.Lever ratio also changed, an...Đọc thêm
CỬA HÀNG LỚN NHẤT
TẠI NHẬT BẢN
COUPON ĐẶC BIỆT,
GIẢM GIÁ, KHUYẾN MÃI
DỊCH VỤ GIAO HÀNG
NHANH, MIỄN PHÍ