410,508 VND
(2,504 JPY)
5 (2 Đánh giá )
rating breakdown
5 Sao |
|
2 |
4 Sao |
|
0 |
3 Sao |
|
0 |
2 Sao |
|
0 |
1 Sao |
|
0 |
Excellent
Sounds good!With moderate softness, it's hard to slip with Fold on the surface. For slimness, I felt Axel opening became narrower, Small hands of myself Axel operation became easier. I always grasp the end of Grip, so it's short as Length 115 mm, so it's easier for the thumb to switch like Blinker.
The disadvantage is that the surface Fold is fine and soft so it is worn out quickly. About half a year 4000 km, the place where the palm strikes is reduced a lot and it became slippery easily. I fixed it so that the remaining Fold is now on top.
Also, since this Grip is thin and short, it may be hard to operate in the Large Kit.
It is recommended for people who like Small people like me! Because it is not too expensive, I would like to repeat again.
Reviews For ariete OEM-RR Grip From Other Webike User
Excellent
It is durable【What made you decide the purchase?】 Since OEM's letters are included, I purchased it because I thought it was as good as OEM or more.
【How was it actually used?】 The Grip used before was cracked in half a year but it is used for 1 year and there is no crack, it is about a little wearing away. When using the same Angle one year 10,000 km when comparing with purchase and photo comparison (I am rolling Hot grip from the top in winter.) I attached the photo of.
【Was it difficult to install? (Hard parts case)】 I cut off the old Grip with Cutter and sprayed Parts cleaner inside the new Grip, I just hated it. It's exactly what I got.
【Please tell me the point of installation and hang (in the case of Hard parts)】 I did not use Grip bond, but it was not twisted and there was no problem.
Hang put a lot of PartsCleaner. Attach as soon as attached.
[Is there anything I was disappointed about?] There was no problem as expected
【Hope for Manufacturer - Please let me know if there are any improvement points】 Though I chose RACERDesign but Thicktle is so thin ○ If it is not an octagon etc., the corner as it is shown on the surface as shown in the picture.
【Have you compared items?】 Pro grip
[Others] I chose Length 115 mm for installation in the SR 400, but it seems to fit even 120 mm.View Detail
Most Viewed Reviews Of ariete Grips
Very Good
ariete OEM-RRGripThe OEMGrip on the Gixxer SF250 was a little slippery and thin, so I replaced it. The unique design of the ScrewScrew makes it easy to grip and prevents slipping. I am also satisfied with the Large size because it is cost-effective and seems to last a long time.View Detail
Excellent
Purchased due to age-related deteriorationI bought this to replace a tear that had appeared due to age-related deterioration.
It has deteriorated in about 2 years since I purchased it new.
The design and texture are better than other manufacturers.
When replacing, heat the Lever and Rubber with boiling water and install while sliding with soap or dish detergent etc.
After installation, rub the Rubber and Lever under running water to remove soap and other slippery residue.View Detail
Poor
Nothing beats an OEM product.I liked the length, stiffness and thickness of the Kawasaki ZXType Grip, so I tried this one with the same design.
After long term use since 2017, it's clear. I will not hesitate to purchase OEM Products next time.
Length and thickness = OEM Product same etc. I like both.
Hardness = soft, but the OEMZXType seems to be even softer.
Durability = The surface has become rough around 2 years old. The surface rubber is in a state of powdering when rubbed.
Thus, the initial performance is not dissatisfied, but when I consider the durability, the OEM product is superior to Large.
So I have already replaced it with an OEM Product.
View Detail
Average
MotoGP Replica, apparently.I don't know much about it, but it seems to be a DUCATI MotoGP Replica.
It feels soft in the grip and very good.
It's also stylish with Logo with Ally.
Now it depends on how long it takes to wear out.View Detail
Excellent
Clutch Side is a little thinImmediately after exchanging from the OEM, I felt it the moment I grabbed it, and that was the general comment
When measured with Caliper, the difference is clearly 30mm on the Axel side and 28mm on the Clutch side …
However, after an hour of riding with the Gloves on, I didn't notice much of a difference
File eye Pattern is Grip good, and the grip to hold Axel is only a little I am thankful
There aren't many 130mm grips that fit the TDM, so hopefully this will continueView Detail
Other Reviews From Japan User(translated)
Excellent
Radipon handled in Mild?attachment
The CBR650R is mounted at the same position angle as the NORMAL.
However, when the handlebar was cut to the Left lock, it interfered with the interior cover next to the Meter, so the interior cover was cut away.
I also purchased a 45° angled banjo adapter for the mesh hose to accommodate the tension of the mesh hose.
・NORMAL (Reserve integrated horizontal master) Impressions of
No complaints on public roads. Familiar feel and very easy to handle.
However, when the brake is set to "hard brake," the rate of increase in braking force relative to the input seems to decrease, and the brake becomes more forceful.
Radipon (Reserve separate body portrait master) Impressions of
It was totally different from what I expected, my expectation was that it would feel like a Rear brake…
It is really a mild and easy-to-handle radipon.
On public roads, it feels like NORMAL! I wonder if it's because NORMAL is the same NISSIN?
But I felt the radipon effect from Breaking a little stronger, and
It can be hung up to a hard brake without effort.
I felt trust that this could stop.View Detail
Very Good
packtalk bold Attached MountI purchased this for use with multiple Helmets. 。
Mount included with the BOLD.
Microphone and speaker are not included and must be purchased separately.View Detail
Excellent
Grip replacementGrip that had been used for a long time was worn out and had to be replaced.
They are soft and dampen vibration.View Detail
Very Good
Works well in everyday life[How is it used?
Used to lick Screw loose.
Was the one you received as per Image?
As per Image.
How was your experience with it?
When used on a strongly tightened Screw, it can be safely and securely removed.
The licked Screw was removed.
It is also useful for DIY Screw removal.
[Points to note]
When used on a licked Screw, it is best to beat it in with a Hammer before use.View Detail
CỬA HÀNG LỚN NHẤT
TẠI NHẬT BẢN
COUPON ĐẶC BIỆT,
GIẢM GIÁ, KHUYẾN MÃI
DỊCH VỤ GIAO HÀNG
NHANH, MIỄN PHÍ