102,940 VND
(628 JPY)
4 (4 Đánh giá )
Very Good
It could be a comfortable Seat, depending on how it's doneGrom's Seat is notorious for being hard and painful on the ass I'm also a fan of Other Brand ProductSeat, but the OEMSeat is a great choice I wondered if there was anything I could do about it
So, I challenged myself to change the Sponge on the part where the buttocks hit
I looked around the DIY store looking for a seat sponge, but I couldn't find anything Search "KIJIMA Ya "NTB The Seat sponge of NTB hit I was attracted to NTB from the aspect of thickness, but it is a little expensive So I decided to go with the decently priced EyeNet
First of all, peel off the skin of Seat of Grom Remove the thin vinyl in the middle of the gloom and remove it
Cut off the part where the buttocks of the seat hits the part of the eye NetSponge for length and thickness This work is the most difficult, it is better to pull the Cutline properly and cut carefully I used the Gold saw, but the Grom Seat is very wide and the work is very easy to cut There are many ways to cut the Seat sponge, and if you search on the net, you can find Hit I want you to find a way that works for you
After cutting, the Sponge is glued in Bond Then cut to the shape of OEM, but it is really difficult to cut the Sponge There are various ways to do this Some people even use grated gold I use Cutter Knife, which is soft Sponge, but Cutter's blade is very soft and easy to cut It's going to be ruined, so I need a few of them
If you finish it appropriately, the shape will still be there after the Seat cover is applied I'm going to finish this place patiently
Once the shape is ready, we put up the agricultural Multi first, replacing the OEM transparent Seat
Then, use the Tucker to re-stretch the OEMSeat cover back together and you're good to go
I skimped a bit on the molding, so it's a bit awkward looking, but it's a lot more comfortable Touring of over 100km is OK. 200km touring was also OK
I wish the product was a little thicker, I need something 3cm thick
The price is so low that you'll want to try it, but if you fail, you'll ruin your Seat, so be careful It is better to prepare for the
The quality of the finished product depends more on your skills than on the ingredients
Reviews For ai-net Miếng bọt biển để sửa ghế (Loại thấp) 20mm From Other Webike User
Excellent
It has good formability and Cushion propertyI am dissatisfied with TIGRA 's Seat, I tried to hear it over..
◆ Problems so far
? It is too soft and Quantity : Pair (for Left and Right) Direction Position and behavior of the vehicle are difficult to grasp.
? It hurts and it hurts with the feeling hitting Seat frame
? with Stages Forced forward and backward, feet are cramped
I went to Seat shop in Motorcycle and consulted but I was offered a price of over 50,000 yen
I decided to try it myself.
◆ Impression after change
As aimed, Seat got harder to normal degree than before.
? Seat's Center is easy to understand (Sitting has decreased)
It is not only hard but also Dumping is working and it can not jump even when passing through Gap.
Since it is a full flat, you can get your favorite Position on a wide Seat.
Work Procedure Material
___ ___ ___ ___ ___ ___ ___ 0
? Adhesion to Sponge Adhesion with synthetic can of Rubber series adhesive G17 with Spray version twice coated
? Sponge is joined by slash cut at Sponge as a way of handling sashimi with kitchen knife
Adjust the surface with Angle Sander
? Paste foam Sponge sprayed Net for reinforcement
? Wrapping the Sponge with MultiSeat for Agriculture Waterproof
? Fix the original skin leather with the leg length 6 mm scales
◆ Other
Seat Outer Cover for CYGNUS thought that it is similar to Smaller than TIGRA's Seat
I could not join orzView Detail
Most Viewed Reviews Of ai-net Other Seat Options / Repair Parts
Very Good
A little slippery, but quite warmusage conditions
It's six degrees outside
clothing
Ed Win, WildeFire a
Rough and Road, Titaniumium Thinsulate inner underwear
Switch-on to maximum pre-heatMODE temperature, then automatically switch to mid-mid temperature But in reality, it takes a little more time to warm up completely
After it warmed up, it was warm enough at low and low temperatures for the above use It became hot on the way, so I raised my butt and lowered the temperature
The power consumption was low at 0.5W, so I wasn't sure if it would be warm enough, but it's enough for my needs It would have been better to have a temperature setting further down on the Low Low temperature
I installed it on the DL1000 V-STROM650, but it's Full face with a thick winter jacket It's difficult to see the Switch directly while riding with the Helmet So you'll have to use no-look to control the Switch while riding, but you'll be able to do it by groping You can see where the Switch is located and the Button has a moderate clicking feeling, so you can operate it somehow You can do this However, you have to remember the current temperature setting because you can't see it (In my case, I only used Low Low temperature, so I went from Pre-HeatMODE to Mid-Medium, (It was only operated once to Low Low temperature afterwards.)
In order to install the DL1000 V-STROM650, you need to make sure that the length of the front side band is as long as possible Because the Surface Fastener that had been left over at home was insufficient, I extended it by connecting the Surface Fastener that had been left over at home If it wasn't, it couldn't be installed
They are using a non-slip Material, but there it is in the WildeFire a V-stop Seat is relatively flat, so I didn't mind that much, but the front I think a downhill Seat motorcycle would be unsettling (If it were leather pants, it would be less slippery.)
I'm expecting it to be less prone to breakage because of the use of Carbon Fibre as the heating element I'm a little worried about the disconnection of this one because it seems to put a load on Wiring from the body to Band It is
It's a shame that the Seat is a little wavy as shown in the picture, but it's satisfactory enough for my usage environment Product
View Detail
Very Good
It doesn't look differentI installed it on GSXS750 The Seat of this motorcycle is Small swing, but when you install it, it is Large Wiring is the tail lamp in the back and put Wiring in the Rear Fender and connect it to Seat I did I haven't run it yet, but it went from strong to medium after about 5 minutes as per the Instruction Manual If you put your hand on the Seat, you can feel the warmth of it It looks like a normal Seat cover or Gel Zab It will keep you warm this winter I would like to post my impressions next time I driveView Detail
Excellent
It has good formability and Cushion propertyI am dissatisfied with TIGRA 's Seat, I tried to hear it over..
◆ Problems so far
? It is too soft and Quantity : Pair (for Left and Right) Direction Position and behavior of the vehicle are difficult to grasp.
? It hurts and it hurts with the feeling hitting Seat frame
? with Stages Forced forward and backward, feet are cramped
I went to Seat shop in Motorcycle and consulted but I was offered a price of over 50,000 yen
I decided to try it myself.
◆ Impression after change
As aimed, Seat got harder to normal degree than before.
? Seat's Center is easy to understand (Sitting has decreased)
It is not only hard but also Dumping is working and it can not jump even when passing through Gap.
Since it is a full flat, you can get your favorite Position on a wide Seat.
Work Procedure Material
___ ___ ___ ___ ___ ___ ___ 0
? Adhesion to Sponge Adhesion with synthetic can of Rubber series adhesive G17 with Spray version twice coated
? Sponge is joined by slash cut at Sponge as a way of handling sashimi with kitchen knife
Adjust the surface with Angle Sander
? Paste foam Sponge sprayed Net for reinforcement
? Wrapping the Sponge with MultiSeat for Agriculture Waterproof
? Fix the original skin leather with the leg length 6 mm scales
◆ Other
Seat Outer Cover for CYGNUS thought that it is similar to Smaller than TIGRA's Seat
I could not join orzView Detail
Very Good
I am saved..Where do you get tired when you go to Touring?
I think it depends on Position but in my case it was "Osiri".
Yes, it is past tense.
From the best to the worst in the improvement of Seat, I think that it is from the maximum amount to the minimum amount.
Personally, I think "COSPER = effect versus cost" is necessary.
When examining various things, we will send Seat from the simplified product to be mounted on Seat and process it ... There are also various countermeasures.
We can respond by inexpensive way that we can process even by ourselves.
It's already Seat more than 30 years ago, but it's not difficult at all.
The necessary tools are Tucker and Scissors.
Osiri does not hurt so I think it is effective.
View Detail
Other Reviews From Japanese Webike user
Excellent
Radipon handled in Mild?attachment
The CBR650R is mounted at the same position angle as the NORMAL.
However, when the handlebar was cut to the Left lock, it interfered with the interior cover next to the Meter, so the interior cover was cut away.
I also purchased a 45° angled banjo adapter for the mesh hose to accommodate the tension of the mesh hose.
・NORMAL (Reserve integrated horizontal master) Impressions of
No complaints on public roads. Familiar feel and very easy to handle.
However, when the brake is set to "hard brake," the rate of increase in braking force relative to the input seems to decrease, and the brake becomes more forceful.
Radipon (Reserve separate body portrait master) Impressions of
It was totally different from what I expected, my expectation was that it would feel like a Rear brake…
It is really a mild and easy-to-handle radipon.
On public roads, it feels like NORMAL! I wonder if it's because NORMAL is the same NISSIN?
But I felt the radipon effect from Breaking a little stronger, and
It can be hung up to a hard brake without effort.
I felt trust that this could stop.View Detail
Very Good
packtalk bold Attached MountI purchased this for use with multiple Helmets. 。
Mount included with the BOLD.
Microphone and speaker are not included and must be purchased separately.View Detail
Excellent
Grip replacementGrip that had been used for a long time was worn out and had to be replaced.
They are soft and dampen vibration.View Detail
Very Good
Works well in everyday life[How is it used?
Used to lick Screw loose.
Was the one you received as per Image?
As per Image.
How was your experience with it?
When used on a strongly tightened Screw, it can be safely and securely removed.
The licked Screw was removed.
It is also useful for DIY Screw removal.
[Points to note]
When used on a licked Screw, it is best to beat it in with a Hammer before use.View Detail
CỬA HÀNG LỚN NHẤT
TẠI NHẬT BẢN
COUPON ĐẶC BIỆT,
GIẢM GIÁ, KHUYẾN MÃI
DỊCH VỤ GIAO HÀNG
NHANH, MIỄN PHÍ