Thép Chromoly (Mạ 3 lớp)
[Spec. ] Nut set
* Xin lưu ý rằng đặc điểm kỹ thuật của sản phẩm có thể thay đổi do lý do nhà sản xuất.
[Cài đặt]
* Trục xe là bộ phận quan trọng.
Hãy chắc chắn rằng nhân viên có trình độ thực hiện công việc lắp đặt tại cửa hàng chuyên nghiệp.
Hãy làm điều đó bằng cách sử dụng công cụ thích hợp phù hợp với hình dạng đầu của trục.
Lớp màng mạ phủ trên bề mặt trục bị xước, gây rỉ sét nếu bạn siết chặt bằng dụng cụ không phù hợp.
Vui lòng xịt dầu mỡ lên bề mặt trục trước khi lắp đặt.
Nó thường không gây ra rỉ từ chính trục vì nó được áp dụng "quy trình mạ ba lớp" của KOOD nguyên bản trên bề mặt trục. Nguyên nhân là do sự khác biệt tiềm năng của kim loại, để ngăn ngừa gỉ từ ổ trục bánh xe, v.v.
Vui lòng tuân thủ các giá trị quy định của nhà sản xuất để siết chặt mô-men xoắn.
Vui lòng xác nhận đai ốc cho xe được lắp bằng đai ốc OEM.
Hãy đảm bảo sử dụng đai ốc mới khi thấy nó trong đai ốc, chẳng hạn như vết xước do rơi và bộ phận chức năng tự khóa. Điều này là để tránh làm hỏng phần ren của trục.
[Về chất lượng sản phẩm]
Về quản lý sản phẩm, nó sản xuất và quản lý trong một hệ thống hoàn hảo nhưng vui lòng liên hệ với chúng tôi trước khi làm việc nếu bạn có bất kỳ sự cố nào.
* Trong mọi trường hợp, chúng tôi không thể phản hồi các khiếu nại và trả lại sản phẩm sau khi làm việc (chẳng hạn như truyền trục qua bánh xe) ở tất cả.
Về rỉ sét
"Trục làm bằng KOOD" đã được trải qua "quy trình mạ ba lớp".
Nó có quá trình xử lý lớp phủ mạnh mẽ so với lớp phủ mạ thông thường. Nó có thể bị rỉ sét tùy thuộc vào tình hình sử dụng nhưng nó không quan trọng về chất lượng.
Nó đang "rỉ sét" ... rỉ sét từ bên ngoài bám trên bề mặt mạ
Rỉ sét chuyển tiếp. Rỉ bên ngoài trên bề mặt mạ
Thiệt hại cho lớp phủ ... Sử dụng không đúng công cụ, đá dẫm hoặc ngã khi lái xe, v.v.
* Rỉ sét không được bảo hành.
Cảm ơn bạn đã hiểu biết của bạn.
[Material] Chromoly steel (3-layer plating finish)
With plated nut
*There may be changes in product specifications due to the manufacturer's reasons.
*Even if the vehicle is compatible, it will not fit if the front forks are not stock or if the vehicle has been customized.
[About the installation]
*Axle shafts are critical parts.
Installation must be carried out by qualified personnel at a professional shop.
・Please use the appropriate tool for the head shape of the shaft.
If the shaft is tightened with an inappropriate tool, the plating film on the shaft surface will be scratched and rust will be caused.
・Before installation, apply grease or other oil to the shaft surface.
The surface of the shaft is treated with KOOD's original "3-layer plating film", so rust will not occur on the shaft itself under normal use.The purpose is to prevent rust transfer from wheel bearings, etc., which is caused by the potential difference of metals.
・Please observe the tightening torque specified by the manufacturer.
・If the vehicle is installed using the stock nut, please check the nut.
If the nut is damaged by tipping over, etc., or if the self-locking part is worn out, be sure to use a new nut.This is to prevent damage to the shaft threads.
[About Product Quality]
・KOOD has taken all possible measures to manage the production. However, if there is any problem, please contact KOOD before the work.
*In no event will KOOD accept any claims or returns after the installation (such as threading the shaft into the wheel).
・About rust
KOOD shafts are treated with a "3-layer plating film".
It is processed with a stronger film than normal plating film.Rust may occur depending on the usage conditions, but there is no problem with the quality.
・Transferred rust: Rust from the outside gets on the plated surface
・Damage to the plating film... Improper use of tools, flying rocks during riding, falls, etc.
[Caution]
In case of KOOD shafts with plated nuts, damaging the threads during installation often happens.
Due to the nature of plating, this is often seen when the plated parts (e.g. KOOD shaft and KOOD nut) mesh with each other or when the threaded part is greaseless.
Please use an anti-corrosive grease such as sledge compound on the screw part when you install it.