[Phù hợp]
· Đường kính tay cầm: Φ22,2
Kẹp đường kính ngoài: Φ33
· Chiều dài tay cầm tương ứng: 115/120 / 130mm
Sản phẩm độc quyền cho xe 12V
[Bao gồm các bộ phận:] Ống co nhiệt để bảo vệ Grip
* Đường kính tay cầm nhỏ (Φ22.2 trở xuống) Xe cộ và thanh inch (.425.4) , Dung lượng pin · Không thể sử dụng cho xe có công suất thấp. (Khởi động cần điện áp 12,5V)
* Để gắn tay áo mở rộng được cung cấp, hãy dán keo vào khu vực có tay áo mở rộng được gắn với kẹp và uốn chắc chắn. Nếu tải cực lớn được áp dụng cho tay áo mở rộng, tay áo mở rộng có thể rơi ra hoặc kẹp kết thúc và mở rộng Xin lưu ý rằng điều này sẽ gây ra thiệt hại cho tay áo.
* Vì nhiệt bị tiêu tan bởi tay cầm, đầu thanh, găng tay và làm mát bằng gió, nhiệt độ cảm giác có thể cảm thấy thấp.
* Sử dụng súng nhiệt để gắn ống co nhiệt đi kèm để bảo vệ tay cầm và khi lò sưởi kẹp nóng, ống bảo vệ kèm theo có thể trở nên mềm và lỏng do nhiệt, vì vậy hãy lắp đặt nó khi không sử dụng máy sưởi. Đó là khuyến cáo.
* Nếu ống bị lỏng sau khi lắp đặt, nhiệt co lại bằng súng nhiệt một lần nữa để tiếp xúc gần với tay cầm.
* Do đặc điểm của ống bảo vệ, tổng chiều dài có dung sai khoảng cộng hoặc trừ 3 mm, và mặt cuối có thể hơi nghiêng, nhưng nó không phải là sản phẩm bị lỗi.
* Đường kính trong của kẹp bên phải là is25,4. Nếu nó nhỏ hoặc lỏng, sử dụng con dấu nhôm kèm theo và điều chỉnh khoảng cách với báng cầm.
* Nó có thể không có sẵn cho những chiếc xe SUZUKI có dung lượng pin và sản xuất năng lượng thấp và những chiếc xe HONDA có pin dưới 7S.
* Xe YAMAHA có thể được sử dụng với xe chạy bằng pin 4B5 trở lên.
[Compatibility]
・Handle Diameter: Φ22.2
・Grip outer diameter: Φ33
・Compatible grip length: 115 / 120 / 130mm
・Exclusive for 12V vehicles
[Components] Heat-shrinkable tube for grip protection
*Not for use with vehicles with small handlebars (Φless than 22.2), inch bars (Φ25.4), or vehicles with low battery capacity or power generation.(A voltage of 12.5V is required for start-up)
*When installing the supplied extension sleeve, apply adhesive to the inside of the extension sleeve where it meets the grip, and crimp it firmly.Please note that extreme load on the extending sleeve may lead to the falling off of the extending sleeve or the breakage of the grip end and the extending sleeve.
*Please understand in advance that you may feel lower temperature due to the heat radiation to the handlebars, bar ends and gloves, and cooling by the driving wind.
*Use a heat gun to install the heat shrink tubing for grip protection provided.Also, when the grip heater is heated, the protective tube may soften and loosen due to the heat, so it is recommended to install it when the heater is not in use.
*If the tube becomes loose after installation, heat shrink it again with a heat gun to make it tighter to the grip.If it still does not adhere, please remove the product as it may be the end of its life.
*The total length of the protective tube has a tolerance of plus or minus 3mm due to its characteristics.The edge of the product may be slightly slanted, but this is not a defect.
*The inner diameter of the right grip is Φ25.4.If the throttle sleeve of the vehicle to be installed has ribs, cut them to a height not lower than the inner diameter of the grip before installation.If the outer diameter of the throttle sleeve is smaller than the inner diameter of the grip and the throttle sleeve is loose, use the supplied aluminum seal to adjust the gap between the throttle sleeve and the grip.
*This product may not be used for SUZUKI vehicles with low battery capacity and power generation, or HONDA vehicles with batteries less than 7S.
*Yamaha vehicles with 4B5 or higher batteries can be used.