Vật liệu ống EX : Titanium
Đường kính ống EX : Φ42. 7
Ống đuôi bên ngoài đường kính : Φ60. 5
* End Baffle đã được cài đặt vào thanh khuếch đại khi vận chuyển.
* Bạn sẽ cần phải thay thế các bước phía sau để loại duy nhất để cài đặt sản phẩm này. Khi cài đặt sản phẩm này, bạn sẽ cần phải cắt (quá trình) Khung của khu vực bước song song.
* Bạn có thể cần phải thay thế các blinker tùy thuộc vào loại blinker.
* Lọc bộ lọc và bu lông thoát phải được thay đổi để loại phẳng. Nắp phẳng và bộ cống được bao gồm trong EX Exhaust Kit. Hãy thay thế chúng khi cài đặt ống xả.
* Có thể sử dụng bộ dụng cụ Nitro RACING Tandem Step Kit Type 2. (Những chiếc xe đã có Nitro RACING Tandem Step Kit 1 có thể gặp sự giao thoa giữa bộ phận giảm âm (trên) Và bộ công cụ bước song song do vị trí hàn cố định của tấm gắn. )
* Khung xả không phù hợp với kiểu treo OEM. Nó phù hợp với laydown gắn kết với cấu trúc M6 lỗ vít.
* Hình ảnh chỉ để tham khảo. Hình ảnh hiển thị có thể khác với sản phẩm thực tế.
[Silencer Specification]
・Thickness: Φ90
・Silencer material: Aluminum
[exhaust pipe specs]
・Assembly method: 4in1
・Tail pipe outer diameter: Φ60.5
・Exhaust pipe diameter: Φ42.7
・Exhaust Pipe Material: Titanium
[Components]
・Assembly part
・Tail pipe
・8 springs
・Silencer
・End baffle
・Silencer band
・Silencer Bracket
・Exhaust pipe per vehicle
[Maintenance Data]
・Drain bolt: Manifold section needs to be detached
・Change oil filter: Manifold section needs to be detached
・Center stand: Not available
*The end baffle is pre-installed on the silencer at the time of shipment.
*Conical titanium silencers V-1 / V-2 / V-3 do not come with a silencer band as a bracket is pre-installed.
Never remove the exhaust baffle from the NITRO RACING silencer.It is also recommended to check and overhaul the silencer's internal sound deadening wool on a regular basis.
It is necessary to change to a single type rearset.In this case, it is necessary to cut off the frame of the pillion step when you replace the stock one with this product.
Depending on the type of blinker, it may be necessary to replace the blinker.
It is necessary to change the filter cover and drain bolt to a flat type.The Flat Cover & Drain KIT is included in the Exhaust Kit and should be replaced when the exhaust is installed.
It is compatible with NITRO RACING Pillion Step KIT Type2.(As to the vehicles already equipped with NITRO RACING Pillion Step KIT Type 1, there is a rare case of interference between the upper part of the silencer and the Pillion Step KIT due to the welding position of the mounting plate.)
The exhaust bracket is not compatible with the stock rear suspension mount.Compatible with laydown mount adaptation with M6 screw hole construction.
* Please note in advance that cancellation and/or return of this product cannot be accepted once the order has been placed.